LHF16KTV
Table 4. Command Definitions (10)
10
Bus Cycles Notes
First Bus Cycle
Second Bus Cycle
Command
Req’d
Oper (1)
Addr (2)
Data (3)
Oper (1)
Addr (2)
Data (3)
Read Array/Reset
1
Write
X
FFH
Read Identifier Codes
Query
Read Status Register
≥ 2
≥ 2
2
4
Write
Write
Write
X
X
X
90H
98H
70H
Read
Read
Read
IA
QA
X
ID
QD
SRD
Clear Status Register
1
Write
X
50H
Block Erase Setup/Confirm
Full Chip Erase Setup/Confirm
Word/Byte Write Setup/Write
Alternate Word/Byte Write
Setup/Write
Multi Word/Byte Write
Setup/Confirm
2
2
2
2
≥ 4
5
5,6
5,6
9
Write
Write
Write
Write
Write
BA
X
WA
WA
WA
20H
30H
40H
10H
E8H
Write
Write
Write
Write
Write
BA
X
WA
WA
WA
D0H
D0H
WD
WD
N-1
Block Erase and (Multi)
Word/byte Write Suspend
Confirm and Block Erase and
(Multi) Word/byte Write Resume
1
1
5
5
Write
Write
X
X
B0H
D0H
Block Lock-Bit Set Setup/Confirm
Block Lock-Bit Reset
Setup/Confirm
2
2
7
8
Write
Write
BA
X
60H
60H
Write
Write
BA
X
01H
D0H
STS Configuration
Level-Mode for Erase and Write
2
Write
X
B8H
Write
X
00H
(RY/BY# Mode)
STS Configuration
Pulse-Mode for Erase
STS Configuration
Pulse-Mode for Write
STS Configuration
Pulse-Mode for Erase and Write
2
2
2
Write
Write
Write
X
X
X
B8H
B8H
B8H
Write
Write
Write
X
X
X
01H
02H
03H
NOTES:
1. BUS operations are defined in Table 3 and Table 3.1.
2. X=Any valid address within the device.
IA=Identifier Code Address: see Figure 4.
QA=Query Offset Address.
BA=Address within the block being erased or locked.
WA=Address of memory location to be written.
3. SRD=Data read from status register. See Table 14 for a description of the status register bits.
WD=Data to be written at location WA. Data is latched on the rising edge of WE# or CE# (whichever goes high
first).
ID=Data read from identifier codes.
QD=Data read from query database.
4. Following the Read Identifier Codes command, read operations access manufacturer, device and block status
codes. See Section 4.2 for read identifier code data.
5. If the block is locked, WP# must be at V IH to enable block erase or (multi) word/byte write operations. Attempts
to issue a block erase or (multi) word/byte write to a locked block while RP# is V IH .
6. Either 40H or 10H are recognized by the WSM as the byte write setup.
7. A block lock-bit can be set while WP# is V IH .
8. WP# must be at V IH to clear block lock-bits. The clear block lock-bits operation simultaneously clears all block
lock-bits.
9. Following the Third Bus Cycle, inputs the write address and write data of ’N’ times. Finally, input the confirm
command ’D0H’.
10. Commands other than those shown above are reserved by SHARP for future device implementations and
should not be used.
Rev. 2.0
相关PDF资料
LH28F160S5HNS-S1 IC FLASH 16MBIT 70NS 56SSOP
LH28F320S3HNS-ZM IC FLASH 32MBIT 110NS 56SSOP
LH28F320SKTD-ZR IC FLASH 32MBIT 70NS 48TSOP
LHF00L28 IC FLASH 16MBIT 70NS 48TSOP
LPM409 CHASSIS STNRD 4SLOT CHASSIS W/INPUT LEAD
LS15RB1201J04 POE SPLITTER 10.8W 12V @0.9A
LT1932ES6#TRMPBF IC LED DRIVR WHITE BCKLGT TSOT-6
LT1937ES5#TRMPBF IC LED DRIVR WHITE BCKLGT TSOT-5
相关代理商/技术参数
LH28F160S3HR-L10 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8/x16 Flash EEPROM
LH28F160S3HR-L13 制造商:未知厂家 制造商全称:未知厂家 功能描述:EEPROM|FLASH|1MX16/2MX8|CMOS|TSSOP|56PIN|PLASTIC
LH28F160S3HT-L10 制造商:Sharp Microelectronics Corporation 功能描述:NOR Flash Parallel 3V 16Mbit 2M/1M x 8bit/16bit 100ns 56-Pin TSOP
LH28F160S3HT-L10A 功能描述:IC FLASH 16MBIT 100NS 56TSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M(2M x 8,1M x 16) 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP(0.724",18.40mm 宽) 供应商设备封装:48-TSOP 包装:托盘
LH28F160S3HT-L13 制造商:未知厂家 制造商全称:未知厂家 功能描述:EEPROM|FLASH|1MX16/2MX8|CMOS|TSSOP|56PIN|PLASTIC
LH28F160S3HT-L75A 制造商:Sharp Microelectronics Corporation 功能描述:
LH28F160S3HT-TF 功能描述:IC FLASH 16MBIT 100NS 56TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:RAM 存储器类型:SDRAM 存储容量:256M(8Mx32) 速度:143MHz 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:90-VFBGA 供应商设备封装:90-VFBGA(8x13) 包装:托盘 其它名称:Q2841869
LH28F160S3-L10 制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:16-MBIT(2MBx8/1MBx16) Smart 3 Flash MEMORY